Cover Supports & Tie-Downs

Stock# 5229524
Portable submersible pump is a great way to remove unwanted water from boats, pool covers, aquariums and sump pits. Convenient and safe, too, because it needs no electrical cord - runs up to 5 hours on three alkaline 'D' batteries.

Stock# 5229227
Boat Cover Support Kit is an easily adjustable cover support system to keep water from accumulating in center of cover. Extends the life of any boat cover by as much as 50%

Stock# 5229281
Boat Cover Support Kit is an easily adjustable cover support system to keep water from accumulating in center of cover. Extends the life of any boat cover by as much as 50%

Stock# 1536148
Plastic Cover Support Cap fits snuggly over a 2x4 piece of wood. Provides more support surface area than a standard telescoping pole.

Stock# 1536253
Plastic Cover Support Base fits snuggly over a 2x4 piece of wood. Provides more support surface area than a standard telescoping pole. Non-skid pads help keep the base secure.

Stock# 5341039
CARVER boat cover support pole is made of 4 anodized aluminum poles that adjust the cover 40" to 70" in height.  Assembly includes a rubber end cap on the bottom pole and a rubber guide tip on the top pole.  Guide tip is designed to mount through grommet installed on cover (Grommet not included).

Stock# 5341040
CARVER vented boat cover support pole is made of 4 anodized aluminum poles that adjust the cover 40" to 70" in height.  The add-on poles telescope from the base while locking into place with a push of a lever.  The vent attaches to the top pole through the boat cover material reducing moisture, heat and mildew under the cover.

Stock# 5229168
1" dia. anodized aluminum pole adjusts from 28" to 48" with rubber tips at both ends.

Stock# 1197103
Keep bimini tops out of the way when not in use with the telescoping bimini top support poles.  7/8" diameter anodized aluminum pole telescopes to raise cover (28" to 48").

Stock# 5229169
1" dia. anodized aluminum pole adjusts from 36" to 64" with rubber tips at both ends.

Stock# 5336230
Quick, easy boat cover center support made of rust-free ABS plastic. Comes with a 9" base, 5" topper with strap slots and six 8-1/4"H x 1-1/2" dia add-on poles raising the cover (12" to 54").

Stock# 1492214
Quick, easy boat cover center support made of rust-free ABS plastic. Comes with a 9" base, 5" topper and six 8-1/4"H x 1-1/2" dia add-on poles raising the cover (12" to 54").

Stock# 5341038
Trailering tie down kit attaches to almost any boat cover that has sewn in tie-down loops. Durable quick release buckles at each end of strap. Designed to go thru loop and around trailer frame.

Stock# 1609278
Reusable Super Tarp Grommets are an excellent tie down aid that can be attached without tools at the exact spot needed to secure your tarp, cover or open air screen room. Heavy-Duty plastic will not rust or stain material.

Stock# 5282157
2 hole screw mount slat sockets, chrome zinc plated finish (1 pair)

Stock# 1576154
The Extend-A-Snap prevents shrinking canvas and covers not fitting by giving an extra 3/4".

Stock# 5229139
Plastic rail mount w/nut & bolt to secure slat inside socket (1 pair)

Stock# 5335039
3-Strand Twisted yellow polypropylene rope has great resistance to rot, mildew, acids, oil, grease, and most chemicals.

Stock# 5335040
3-Strand Twisted yellow polypropylene rope has great resistance to rot, mildew, acids, oil, grease, and most chemicals.

Stock# 5335041
3-Strand Twisted yellow polypropylene rope has great resistance to rot, mildew, acids, oil, grease, and most chemicals.

Stock# 5335042
3-Strand Twisted yellow polypropylene rope has great resistance to rot, mildew, acids, oil, grease, and most chemicals.